Auszug aus dem Standard:

1.4 Basic Legal Provisions It shall be a matter of course for Blue Angel eco-labelled products to comply with current laws and regulations, especially the following ones, as amended: • Ecodesign Regulation for computers and computer servers (617/2013/EU)3, • WEEE Directive (2012/19/EU)4, transposed into German law by the German Elektro- und Elektronikgesetz (ElektroG)5 (Electrical and Electronic Equipment Act) governing the disposal of electronic devices, [...] • Substance requirements defined by the EU Chemicals Regulation REACH (EC/1907/2006)8 and the POP Regulation (EC/850/2004)9, [...]

Referenzdokumente:

1.4 Basic Legal Provisions 3.4.1 Plastics used in Housings and Housing Parts ....................................................... 12

Auszug aus dem Standard:

3.4.1 Plastics used in Housings and Housing Parts [...] Halogenated polymers shall not be permitted in housings and housing parts. Nor may halogenated organic compounds be added as flame retardants. Nor shall any flame retardants be permitted which are classified under the CLP Regulation as carcinogenic of Category Carc. 2 or as hazardous to waters of Category Aquatic Chronic 1.

Referenzdokumente:

3.4 Material Requirements

Auszug aus dem Standard:

3.4.1 Plastics used in Housings and Housing Parts The plastics used in housings and housing parts must not contain, as constituent components, any substances with the following characteristics15: a) Substances that have been identified as substances of very high concern according to Regulation (EC) No 1906/2006 (REACH) 8 and have been included in the list (so-called Candidate List) set up in accordance with REACH, Article 59(1).16 b) Substances that have been classified according to the CLP Regulation17 in the following hazard categories or meet the criteria for such classification18:  carcinogenic of category Carc. 1A or Carc. 1B  mutagenic of category Muta. 1A or Muta. 1  reprotoxic of category Repr. 1A or Repr. 1B. Halogenated polymers shall not be permitted in housings and housing parts. Nor may halogenated organic compounds be added as flame retardants. Nor shall any flame retardants be permitted which are classified under the CLP Regulation as carcinogenic of Category Carc. 2 or as hazardous to waters of Category Aquatic Chronic 1. The hazard statements (H-phrases) assigned to the hazard categories can be seen from Fehler! V erweisquelle konnte nicht gefunden werden.. The following shall be exempt from this requirement: • fluoroorganic additives (as, for example, anti-dripping agents) used to improve the physical properties of plastics, provided that they do not exceed 0.5 weight percent; • plastic parts weighing 25 grams or less, where - with regard to keyboards - the total weight of all key caps shall be the decisive factor in determining the mass. CLP Regulation (EC) No 1272/2008 Appendix B Assignment of Hazard Categories and Hazard Statements The following table assigns the respective hazard statements (H statements) to the hazard categories of the substances generally excluded. [...] H410 Very toxic to aquatic life with long lasting effects.

Referenzdokumente:

3.4 Material Requirements Appendix B Assignment of Hazard Categories and Hazard Statements

Auszug aus dem Standard:

3.4.1 Plastics used in Housings and Housing Parts The plastics used in housings and housing parts must not contain, as constituent components, any substances with the following characteristics15: a) Substances that have been identified as substances of very high concern according to Regulation (EC) No 1906/2006 (REACH) 8 and have been included in the list (so-called Candidate List) set up in accordance with REACH, Article 59(1).16 b) Substances that have been classified according to the CLP Regulation17 in the following hazard categories or meet the criteria for such classification18:  carcinogenic of category Carc. 1A or Carc. 1B  mutagenic of category Muta. 1A or Muta. 1  reprotoxic of category Repr. 1A or Repr. 1B. Halogenated polymers shall not be permitted in housings and housing parts. Nor may halogenated organic compounds be added as flame retardants. Nor shall any flame retardants be permitted which are classified under the CLP Regulation as carcinogenic of Category Carc. 2 or as hazardous to waters of Category Aquatic Chronic 1. The hazard statements (H-phrases) assigned to the hazard categories can be seen from Fehler! V erweisquelle konnte nicht gefunden werden.. The following shall be exempt from this requirement: • fluoroorganic additives (as, for example, anti-dripping agents) used to improve the physical properties of plastics, provided that they do not exceed 0.5 weight percent; • plastic parts weighing 25 grams or less, where - with regard to keyboards - the total weight of all key caps shall be the decisive factor in determining the mass. Appendix B Assignment of Hazard Categories and Hazard Statements The following table assigns the respective hazard statements (H statements) to the hazard categories of the substances generally excluded. CLP Regulation (EC) No 1272/2008 Carcinogenic Substances Carc. 1A Carc. 1B H350 May cause cancer. Carc. 1A Carc. 1B H350i May cause cancer by inhalation. Carc. 2 H351 Suspected of causing cancer. Mutagenic Substances Muta. 1A Muta. 1B H340 May cause genetic defects. Reprotoxic Substances Repr. 1A Repr. 1B H360D May damage the unborn child. Repr. 1A Repr. 1B H360F May damage fertility. Repr. 1A Repr. 1B H360FD May damage fertility. May damage the unborn child. Repr. 1A Repr. 1B H360Df May damage the unborn child. Suspected of damaging fertility. Repr. 1A Repr. 1B H360Fd May damage fertility. Suspected of damaging the unborn child. Environmentally Hazardous Substances Aquatic Chronic 1 H410 Very toxic to aquatic life with long lasting effects.

Referenzdokumente:

3.4 Material Requirements Appendix B Assignment of Hazard Categories and Hazard Statements

Auszug aus dem Standard:

1.4 Basic Legal Provisions It shall be a matter of course for Blue Angel eco-labelled products to comply with current laws and regulations, especially the following ones, as amended: [...] • RoHS Directive (2011/65/EU)6 governing the contents of hazardous substances in the products transposed into German law by the German Elektro- und Elektronikgeräte-StoffVerordnung (ElektroStoffV) (Ordinance on the Restriction of the Use of Hazardous Substances in Electrical and Electronic Equipment)7 DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 8 June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment ANNEX II Restricted substances referred to in Article 4(1) and maximum concentration values tolerated by weight in homogeneous materials Lead (0,1 %) Mercury (0,1 %) Cadmium (0,01 %) Hexavalent chromium (0,1 %) Polybrominated biphenyls (PBB) (0,1 %) Polybrominated diphenyl ethers (PBDE) (0,1 %)

Referenzdokumente:

DIRECTIVE 2011/65/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 8 June 2011 ANNEX II

Auszug aus dem Standard:

3.4.1 Plastics used in Housings and Housing Parts The plastics used in housings and housing parts must not contain, as constituent components, any substances with the following characteristics15: a) Substances that have been identified as substances of very high concern according to Regulation (EC) No 1906/2006 (REACH) 8 and have been included in the list (so-called Candidate List) set up in accordance with REACH, Article 59(1).16 b) Substances that have been classified according to the CLP Regulation17 in the following hazard categories or meet the criteria for such classification18:  carcinogenic of category Carc. 1A or Carc. 1B  mutagenic of category Muta. 1A or Muta. 1  reprotoxic of category Repr. 1A or Repr. 1B. Halogenated polymers shall not be permitted in housings and housing parts. Nor may halogenated organic compounds be added as flame retardants. Nor shall any flame retardants be permitted which are classified under the CLP Regulation as carcinogenic of Category Carc. 2 or as hazardous to waters of Category Aquatic Chronic 1. [...]

Referenzdokumente:

3.4 Material Requirements

Auszug aus dem Standard:

1.4 Basic Legal Provisions It shall be a matter of course for Blue Angel eco-labelled products to comply with current laws and regulations, especially the following ones, as amended: [...] • External Power Supply Regulation (278/2009/EC)10 fixing the energy efficiency requirements for external power supplies, [...] 3.1 Energy and Power Consumption of Computers Computers, as defined in para. 1.5.1 shall meet ENERGY STAR Program Requirements for Computers applicable to the specific type of computer, as amended at the time of application (current version: 6.1).

Referenzdokumente:

1.4 Basic Legal Provisions 3 General Requirements

Auszug aus dem Standard:

The product documents shall at least provide the following user information: a) Energy consumption (ETEC) in kilowatt hours per year (kWh/a) as well the power consumption in different operating modes according to para. Fehler! Verweisquelle k onnte nicht gefunden werden. Fehler! Verweisquelle konnte nicht gefunden werden.. Also included shall be instructions for setting the devices into energy-saving operating modes as well as information on further energy-saving options (e.g. reduction of screen brightness, complete disconnection from the mains). If a maximum power value is set for computers in accordance with ENERGY STAR - instead of energy consumption (ETEC) - the product documents shall give the measured power values (in watts): PTEC for workstations and PLONG_IDLE as well as POFF for small-scale servers.

Referenzdokumente:

3.6 Product Documents

Auszug aus dem Standard:

Referenzdokumente:

Auszug aus dem Standard:

3.3.2 Material Selection [...] • Plastic parts with an mass greater than 25 grams each and an even surface area of more than 200 sq.mm. must be permanently marked in accordance with ISO 11469 with due regard to ISO 1043, Parts 1 to 4. Transparent plastic parts the function of which requires transparency (e.g. visible plastic films in displays) shall be exempt from marking according to ISO 11469.

Referenzdokumente:

3.3 Recyclable Design

Auszug aus dem Standard:

3.3.2 Material Selection • The following applies to plastic parts with a mass greater than 25 grams as well as to key caps, provided that their total mass is greater than 25 grams: A maximum of 4 types of plastic may be used for these parts. The plastic housings may consist of two separable polymers or polymer blends at the most. • Plastic parts with an mass greater than 25 grams each and an even surface area of more than 200 sq.mm. must be permanently marked in accordance with ISO 11469 with due regard to ISO 1043, Parts 1 to 4. Transparent plastic parts the function of which requires transparency (e.g. visible plastic films in displays) shall be exempt from marking according to ISO 11469. • It shall not be permitted to apply metallic coatings to plastic housing parts. Exception: plastic housing parts of notebook computers may have a metallic coating provided that such coating is technically required. However, galvanic coatings of plastic housing parts shall not be permitted. • (Post-consumer) recyclate material may be used in housing parts and chassis. It may be used on a percentage basis. • 90% of the mass of plastics and of the metals of housing parts and chassis must be recyclable by material (this does not mean the recovery of thermal energy by incineration).

Referenzdokumente:

3.3 Recyclable Design

Auszug aus dem Standard:

3.3.1 Structure and Connection Technology The following applies to computers and keyboards: • The devices to be Blue Angel eco-labelled must be so designed as to allow easy disassembly for recycling purposes to make sure that housing parts, Chassis, batteries (if any), display units (if any) and printed circuit boards can be separated as fractions from materials of other functional units and, if possible, recycled by the type of material. They shall be so designed as to allow manual disassembly by a waste disposal company by the use of universal tools 14 and it shall be possible for a single person to disassemble the device. • Batteries/accumulators (if any) must be easy to remove without the use of any tools or with the use of universal tools. • Electrical/electronic components must be easy to remove from the housing.

Referenzdokumente:

3.3 Recyclable Design

Auszug aus dem Standard:

1.4 Basic Legal Provisions It shall be a matter of course for Blue Angel eco-labelled products to comply with current laws and regulations, especially the following ones, as amended: • Ecodesign Regulation for computers and computer servers (617/2013/EU)3, • WEEE Directive (2012/19/EU)4, transposed into German law by the German Elektro- und Elektronikgesetz (ElektroG)5 (Electrical and Electronic Equipment Act) governing the disposal of electronic devices 3.6 Product Documents [...] The product documents shall at least provide the following user information: [...] e) Instructions for environmentally sound disposal at the end of the life cycle in accordance with the German Elektrogesetz (Electrical and Electronic Equipment Act), f) Information on manufacturer-operated product take-back programs to allow reuse (if any), [...]

Referenzdokumente:

1.4 Basic Legal Provisions 3.6 Product Documents 3.6 Product Documents ........................................................................................... 15

Auszug aus dem Standard:

1.4 Basic Legal Provisions It shall be a matter of course for Blue Angel eco-labelled products to comply with current laws and regulations, especially the following ones, as amended: [...] • WEEE Directive (2012/19/EU)4, transposed into German law by the German Elektro- und Elektronikgesetz (ElektroG)5 (Electrical and Electronic Equipment Act) governing the disposal of electronic devices, [...] 3.3.1 Structure and Connection Technology The following applies to computers and keyboards: • The devices to be Blue Angel eco-labelled must be so designed as to allow easy disassembly for recycling purposes to make sure that housing parts, Chassis, batteries (if any), display units (if any) and printed circuit boards can be separated as fractions from materials of other functional units and, if possible, recycled by the type of material. They shall be so designed as to allow manual disassembly by a waste disposal company by the use of universal tools14 and it shall be possible for a single person to disassemble the device. 3.6 Product Documents The product documents shall at least provide the following user information: e) Instructions for environmentally sound disposal at the end of the life cycle in accordance with the German Elektrogesetz (Electrical and Electronic Equipment Act), g) If the computer is a notebook computer the product documents shall additionally include information according to para. 4 (Special Requirements for Notebook Computers): [...]  A note advising the user that batteries/accumulators must not be disposed of with the normal household waste but instead should be taken to a waste collection facility.

Referenzdokumente:

1.4 Basic Legal Provisions 3.3 Recyclable Design 3.6 Product Documents

Auszug aus dem Standard:

3.6 Product Documents The product documents included with the computer shall include both the technical specifications and the environment and health-related user information. These documents shall either be installed on the computer, supplied as a CD-ROM or in printed form, preferably on recycled paper, together with the device or made available on the Internet from the time of delivery for a period of at least 5 years after the end of production. The product documents for keyboards need only include the relevant keyboard-related information (Nos. 2., 4., 5. und 6.). The product documents shall at least provide the following user information: a) Energy consumption (ETEC) in kilowatt hours per year (kWh/a) as well the power consumption in different operating modes according to para. Fehler! Verweisquelle k onnte nicht gefunden werden. Fehler! Verweisquelle konnte nicht gefunden werden.. Also included shall be instructions for setting the devices into energy-saving operating modes as well as information on further energy-saving options (e.g. reduction of screen brightness, complete disconnection from the mains). If a maximum power value is set for computers in accordance with ENERGY STAR - instead of energy consumption (ETEC) - the product documents shall give the measured power values (in watts): PTEC for workstations and PLONG_IDLE as well as POFF for small-scale servers. b) Information on the provision of spare parts according to Fehler! Verweisquelle konnte nicht gefunden werden. (Spare Parts AvailabilityFehler! Verweisquelle konnte nicht gefunden werden.), c) Options for expanding the capacity according to para. 3.2.2 (Capacity Expansion), d) Sound power level in all operating modes (provided that the requirements are applicable) according to para. 3.5 (Noise Emissions), e) Instructions for environmentally sound disposal at the end of the life cycle in accordance with the German Elektrogesetz (Electrical and Electronic Equipment Act), f) Information on manufacturer-operated product take-back programs to allow reuse (if any), g) If the computer is a notebook computer the product documents shall additionally include information according to para. 4 (Special Requirements for Notebook Computers):  Instructions on how to remove and replace the battery/accumulator or battery/accumulator pack according to para. 4.2 (Replaceability),  Indication of nominal capacity, nominal voltage and type designation according to para. 4.4 (Battery/Accumulator Marking) as well as instructions for decoding if the battery/accumulator displays a coded date of manufacture,  Indication of the minimum achievable full charge cycles according to para. 4.5 (Battery/Accumulator Durability),  Information on the software tools for battery/accumulator status reading and for battery/accumulator protection according to para. 4.6 (Battery/Accumulator Status and Battery/Accumulator Protection Software),  A note advising the user that batteries/accumulators must not be disposed of with the normal household waste but instead should be taken to a waste collection facility.

Referenzdokumente:

3.6 Product Documents

Auszug aus dem Standard:

3.5 Noise Emissions Compliance with the following requirements needs to be verified only if mechanical fans (e.g. CPU/GPU fan, power pack fan, system fan, RAM fan, hard disk fan), mechanical hard disk drives and/or optical drives are integrated into the computer. If none of these components are integrated into the computer the requirements shall be considered met. The requirements for keyboards shall apply independently of a computer. The evaluation of noise emissions is based on the specification of the declared A-weighted sound power levels LWAd in decibel (dB) to the first decimal place. In doing so, it must be made sure that, in the case of configuration variants of structurally identical devices, the measurements are performed on the loudest individual components. Determination of the declared A-weighted sound power levels The A-weighted sound power levels LWA(1..4) shall be determined in accordance with ISO 7779 in the operating modes as described in the Annex to ECMA-74. a) LWA(1) shall be determined in the C.15.3.2 mode - "idle mode". b) LWA(2) shall be determined in the C.15.3.3 g) mode - "active mode". c) LWA(3) shall be determined in the C.19.3.2 mode „optical drive". d) LWA(4) shall be determined in the C.5.3.1 „keyboard“. [...]

Referenzdokumente:

3.5 Noise Emissions